✨ installing aod transmission. Ford AOD Transmission Installation and Swapping Guide by DIY Ford 2019-07-11

✨ installing aod transmission Rating: 5,8/10 1722 reviews

Install An Automatic Overdrive

✨ installing aod transmission

If start-up is uneventful you are good to continue. Always remember that the throttle should pull the cable. If the vibration still exists, take the vehicle to a driveline specialist who can examine it for vibration issues. However, the craftmanship of the original conversion left a bit to be desired. You want cable tension just as the throttle is coming off idle. There is only one way to install a flexplate because the bolt-hole pattern works only one way to prevent improper installation.

Next

Install An Automatic Overdrive

✨ installing aod transmission

Make sure the torque converter is properly seated. Add fluid in small amounts and allow the transmission to reach operating temperature. You want a balance between cable tension and no cable tension with the cable slack, yet just short of tension. With the accelerator pedal at rest, the throttle should be at idle stop. The shift lever went on with no problem, but the cable bracket was a trick. When the throttle is opened, cable movement and tension increase, modulating line pressure accordingly via the throttle valve, which is what you want when power is applied.

Next

Tips & Tricks for Installing a Lokar AOD Transmission TV Cable Kit

✨ installing aod transmission

Then I tackled the transmission end of the cable. These numbers are factory specifications. The Lokar bracket that comes with the kit is really engineered for a throttle cable, so I had to adjust the bracket all the way in towards the carburetor, and it still barely has clearance for the throttle rod. If you are so inclined, you can fabricate your own crossmember, but driveshaft fabrication must be performed by a qualified professional. The engine labors mildly and you feel a solid connection with the drive axle. If the torque converter will not turn when you mate the bellhousing to the engine, you need to lower the transmission and remate the converter and front pump.

Next

Install An Automatic Overdrive

✨ installing aod transmission

Locate the flat spots on the converter snout and front pump rotor. Sometimes custom installations clear and sometimes they don’t. To adjust the self-locking rail adjuster, push in on the lock, which releases the notched rail and allows you to move the notched rail back and forth to adjust cable tension. Start by adding fluid to the converter and greasing the torque converter hub, seals and shaft to ensure a smooth installation with out any cut seals. Back the throttle valve rod adjustment at the carburetor or throttle body all the way out.

Next

Tips & Tricks for Installing a Lokar AOD Transmission TV Cable Kit

✨ installing aod transmission

After several google searches and various tests, I finally pressed my finger against the shift lever and found it moved just the slightest bit. If you can provide the dimensions, most shops can fabricate the crossmember you need. It also calls for a pressure gauge at the throttle valve pressure port on the passenger side of the transmission case. This was not really discussed anywhere in any of the instructions. The torque converter must be replaced because it is virtually impossible to flush out contaminants. Work out a game plan while you still have transportation.

Next

Ford Torque Converter Install

✨ installing aod transmission

This is a Continental torque converter from Auto-Rite Transmissions, which has furnace-welded fins for structural integrity. With the flat side against the transmission case, I was just able to get it to thread. It clears virtually everything including aftermarket headers. Most late-model automatics have a locking torque converter, which engages when the transmission shifts into Overdrive. When the shifter is moved into gear, throttle valve pressure should rise 2 to 35 psi. Mustangs Plus sent us the aluminum driveshaft that’s a bolt-in swap. The gauge instantly dropped to 0.

Next

Install An Automatic Overdrive

✨ installing aod transmission

As you move the manual shifter, you move a cam that moves this switch back and forth. The input shaft turns clutches and planetary gear sets to get power to the driveshaft yoke. It goes up through the pan and has a nut that goes on the back of it to support the tension. Clearance problems reared their ugly heads with our exhaust system. Then, tighten the nut, making sure the centering pin arrow b in the case remains and that both the manual and throttle valve kickdown linkages are properly reinstalled inside. When installing a new or modified driveshaft, harmonics balance can be an issue.

Next

Ford Torque Converter Install

✨ installing aod transmission

The Lokar kit comes with a longer bolt to replace the original pan bolt. The cable should be slack, with the throttle closed and the accelerator linkage relaxed. Examine the dipstick at a hot idle and look for evidence of foaming air bubbles and any debris. The first thing I did was add a to the Holley carburetor. Wouldn’t it be nice if you could restore a classic Mustang in such a way that it would yield closer to 30-mpg highway, with less wear and tear on that vintage 289? Then test-drive and pay close attention to shift quality and timing. Foaming creates air in the fluid, undermining hydraulics and lubrication. You have a choice of steel or aluminum.

Next

Ford AOD Transmission Installation and Swapping Guide by DIY Ford

✨ installing aod transmission

Step 1: Verify Torque Converter Fitment Before installation, check torque converter dimensions. Step 3: Install Flexplate Use the reference mark you made during driveshaft removal to get the flexplate lined up perfectly for installation. The more tension you have, the later and harder the shift. Make sure the parking brake is set and the selector is in park. Strange fact, the allen wrench sent in the Lokar cable kit did not actually fit the set screw in the stop adjuster. Place both at 12 and 6 o’clock, and then slip the converter snout into the pump rotor.

Next